"Grand Brass Lamp Parts is Redesigning the Lighting Industry. New Lamp Parts and Lighting Products Frequently Available so Check Back Often! Let us be your lamp and light making parts supplier. We have a Large Inventory of replacement lamp glass shades and lighting glass such as necked fitter glass shades, torchiere floor lamp glass shades, student shades, school house glass shades and many styles of antique reproduction glass shades.Large selection of DIY lighting products. We carry a Large selection of lamp parts and chandelier parts including lamp sockets, crystal prisms, chandelier chain and ceiling canopies, lamp wire, cord switches, lamp dimmers, floor lamp glass, fixture chain and all the supplies for making lamps. We are the oldest supplier of lamp making supplies in the USA. Grand Brass Lamp Parts has served the Retail and Wholesale lamp parts, lighting parts, and chandelier parts industry since 1913. Can I get these LUT-MLC things too? Will that fix my issue? Please help.Lamp Parts | Lighting Parts | Retail and Wholesale Lighting Supply | Lamp Making Supplies It helped but didn’t fix it completely.and twice the price. Ow it pulses like the others still but both will stop after a few seconds. I swapped that switch out for a pro model dimmer and wired the neutral into it. The one that has only two cans pulses much faster and then only one turns off completely. 1 dimmer controls 8 cans, 3 set up in 3 bedrooms of 4 cans each, and a breakfast nook that has 2 cans. You can only see it at night when it is pitch black. I also found a thread where Lutron engineers. After some online searches, it seemed as if this was a rather common issue and a few solutions had been proposed: - Use an LUT-MLC: this did somewhat work but generated some buzzing when the light was on at 100. BUT.when they turn off, they will pulse very faintly for a few seconds before finally shutting completely off. I had an issue with ghosting using a a Lutron PD-6WCL and Shine Decor Neon LED Rope. They dim perfectly and have no issues when on and on the app I can go from 100% down to 1% with no issues. According to the PD-6WCL sheet, the minimum load for the dimmer is 25W. My contractor put the same retrofit led cans in every room (do not know the brand but I do love them). I bought a Caseta Pro bridge and a bunch of PD-6WCL dimmers. Would this go on each circuit that's flickering? I'm happy to buy and try but it seems to not be readily available to consumers. None of my dimmers came with this and a post in this community stated it wasn't tested with Caseta. According to the PD-6WCL sheet, the minimum load for the dimmer is 25W. Taking out one of the 5W LED bulbs and putting in a 7W LED bulb has made the fixture stable without flickering. In another forum, it was suggested to use a LUT-MLC. It seemed to have fixed the issue until today when they started acting up again (flashing instead of fading on, even at full brightness). This happens whether or not the kitchen lights are on. These lights are not affected my the kitchen lights with the Pro dimmer. When I turn on the switch, they light up full power. When I pull the FASS out on the switch, then they dim and eventually fade out. We put in a Caseta switch to control those lights. My electrician has not seen this before but admittedly has not had a lot of experience with the Lutron Caseta dimmers.Īnother oddity, I have four small LED stairway lights. Pulling out the FASS on say the LR lights lowers the flickering but does not eliminate. If I remove the Pro, no flickering anywhere. The only lights that flicker are 5" lights on a Caseta dimmer, but only when the pro is installed. If I remove a Caseta from the living room for example and put a regular switch back in, no more flickering in the LR. The flickering is much more pronounced when the kitchen lights are dimmed but still happens when the kitchen lights are on full. When the kitchen lights are on, the lights in the living room, family room, and in the stairway area all flicker when off. When the kitchen lights are off, everything is fine. The problem started when the Pro was installed in the kitchen. LR/FR/Stairs have FEIT LED 5" retrofit can lights (CELEDRT56/850/927/2), kitchen has a higher wattage 5" ( LEDR56/827 I believe) and the bedroom has 4". 1 Caseta Pro dimmer with neutral connected in the kitchen due to load being >150w. LUT-MLC load adapter Note: LUT-MLC is included to ensure proper function with CFL, LED, ELV, and uorescent lighting. Note: This equipment has been tested and found to comply with the limits for. could void the user’s authority to operate this equipment. 4 standard Caseta dimmers - 1 in MBR, 1 in Family Room, 1 in Living Room, and 1 in a stair area. Modications not expressly approved by Lutron Electronics Co., Inc. I have 5 Lutron Caseta dinners in my house. Looking for some assistance with a rather unique problem.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |